Ultra Bite

98 Series Endmill

Ultra-Bite Series
Ultra-Bite Series
High Performance

Finish
Rough
 
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended

98 Ultra-Bite Series

Stock Code d1f8 l2 l1 d2h6 Ch R Z
* 98303046/97303046W 3 6 46 6 Ch 0.03 - 3
* 98403002/98403002W 3 6 46 6 - 0.2 4
* 98404002/98404002W 4 12 58 6 - 0.2 4
98404005/98404005W 4 12 58 6 - 0.5 4
* 98404010/98404010W 4 12 58 6 - 1 4
* 98406002/98406002W 6 14 58 6 - 0.2 4
* 98406005/98406005W 6 14 58 6 - 0.5 4
98406010/98406010W 6 14 58 6 - 1 4
* 98408002/98408002W 8 23 64 8 - 0.2 4
* 98408005/98408005W 8 23 64 8 - 0.5 4
* 98408020/98408020W 8 23 64 8 - 2 4
* 98410002/98410002W 10 24 73 10 - 0.2 4
* 98410005/98410005W 10 24 73 10 - 0.5 4
98410010/98410010W 10 24 73 10 - 1 4
98410020/98410020W 10 24 73 10 - 2 4
* 98412002/98412002W 12 28 82 12 - 0.2 4
* 98412005/98412005W 12 28 82 12 - 0.5 4
98412010/98412010W 12 28 82 12 - 1 4
98412020/98412020W 12 28 82 12 - 2 4
98412040/98412040W 12 28 82 12 - 4 4
98416002/98416002W 16 38 93 16 - 0.2 4
* 98416005/98416005W 16 38 93 16 - 0.5 4
98420050/98420050W 20 44 105 20 - 5 4
5
SPECIAL 98408064/98408064W 8 17 64 8 Ch 0.3 - 4

Feed Per Tooth (mm/tooth)

Ø ap=1Ø ap=0.50Ø ae=0.35Ø ae=0.30Ø ae=0.25Ø ae=0.20Ø ae=0.15Ø ae=0.10Ø
3 0.006 0.007 0.007 0.007 0.007 0.008 0.008 0.01
4 0.008 0.01 0.009 0.009 0.01 0.01 0.011 0.014
5 0.011 0.014 0.012 0.013 0.013 0.014 0.015 0.019
6 0.014 0.0l7 0.0l5 0.016 0.0l7 0.018 0.02 0.024
8 0.02 0.024 0.022 0.023 0.024 0.025 0.028 0.034
10 0.027 0.029 0.03 0.031 0.032 0.034 0.038 0.046
12 0.035 0.04 0.04 0.041 0.043 0.045 0.05 0.061
16 0.055 0.065 0.061 0.063 0.066 0.069 0.077 0.094
20 0.075 0.09 0.083 0.086 0.09 0.094 0.105 0.128

Cutting Parameters

Material Slotting Shoulder Milling Finish Milling
ap=1.0 - 0.5Ø ap=1.5Ø   / ae=0.35 - 0.20Ø ap=1.5Ø   / ae=0.20 - 0.10Ø
Vc (m/min)  Vc (m/min)  Vc (m/min) 
AISI 304 - 416 - 420 50-70 70-90 80-100
AISI 316 - 440 45-70 55-80 60-90
17-4 PH 15-5 PH 45-70 55-80 60-90
Chrome-Cobalt alloy  30-50 35-55 40-70
Cr - Co AJ/oys 60-80 65-85 70-90
Duplex F51 60-80 65-85 70-90
Super duplex F55 30-50 40-60 50-70
HRSA hastelloy 30-50 40-60 50-70
HRSA incoinel 625 30-50 40-60 50-70
HRSA incoinel 718 30-50 40-60 50-70
HRSA nimonic 60-80 70-90 80-90
Titanium 60-80 70-90 80-90
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended