Ultra Bite

97 Series Endmill

Ultra-Bite Series
Ultra-Bite Series
High Performance

Finish
Rough
 
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended

97 Series Endmill

STOCK CODE d1h9 l2 l3 d3 l1 d2h6 Ch R Z
97403058P/97403058PW 3 6 15 2.8 58 6 - R0.15 4
* 97403051/97403051W 3 6 - - 51 6 - R0.15 4
* 97403000W 3 6 - - 50 6 0 - 4
* 97403058XL/97403058WXL 3 10 - - 58 6 - R0.15 4
97404058P/97404058PW 4 9 18 3.8 58 6 - R0.15 4
* 97404058/97404058W 4 9 - - 58 6 - R0.15 4
97404058XL/97404058WXL 4 12 19 3.8 58 6 - R0.15 4
* 97404000W 4 12 - - 50 6 0 - 4
* 97405000W 5 12 - - 50 6 0 - 4
* 97405058/97405058W 5 15 - - 58 6 - R0.15 4
97405058P/97405058PW 5 13 18 4.8 58 6 - R0.15 4
* 97406058/97406058W 6 16 23 5.7 58 6 - R0.15 4
* 97406000W 6 15 - - 50 6 0 - 4
* 97408064/97408064W 8 20 27 7.7 64 8 0.2 - 4
* 97408000W 8 20 - - 64 8 0 - 4
* 97410073/97410073W 10 26 32 9.5 73 10 0.2 - 4
* 9741000W 10 26 - - 73 10 0 - 4
* 97412082/97412082W 12 28 38 11.5 82 12 0.3 - 4
* 97412082XL/97412082WXL 12 36 - - 82 12 0.3 - 4
* 97416093P/97416093PW 16 36 44 15.5 93 16 0.3 - 4
* 97416093/97416093W 16 36 - - 93 16 0.3 - 4
* 97420105/97420105W 20 38 54 19.5 105 20 0.3 - 4
SLOT * 97412082 XPER SLOT 12 28 36 11.7 82 12 0.1 - 4

Feed Per Tooth (mm/tooth)

Ø ap=1.5Ø ap=1Ø ap=0.50Ø ae=0.35Ø ae=0.30Ø ae=0.25Ø ae=0.20Ø ae=0.15Ø ae=0.10Ø
3 0.004  0.006  0.008  0.010  0.012  0.016  0.020  0.030  0.0420 
4 0.007  0.009  0.013  0.016  0.02 0.025  0.030  0.038  0.0490 
5 0.010  0.013  0.017  0.020  0.025  0.031  0.036  0.046  0.0580 
6 0.014  0.018  0.022  0.026  0.030  0.037  0.044  0.050  0.0620 
8 0.020  0.025  0.029  0.034  0.040  0.048  0.056  0.064  0.0730 
10 0.026  0.030  0.038  0.042  0.050  0.059  0.067  0.076  0.0880 
12 0.035  0.042  0.053  0.060  0.070  0.080  0.092  0.102  0.1150 
16 0.042  0.060  0.082  0.100  0.11 0.120  0.130  0.138 0.1500 

Cutting Parameters

Material Slotting Shoulder Milling Finish Milling
ap=1.0 - 0.5Ø ap=1.5Ø   / ae=0.35 - 0.20Ø ap=1.5Ø   / ae=0.20 - 0.10Ø
Vc (m/min)  Vc (m/min)  Vc (m/min) 
AISI 304 - 416 - 420 50-70 70-90 80-100
AISI 316 - 440 45-70 55-80 60-90
17-4 PH 15-5 PH 45-70 55-80 60-90
Chrome-Cobalt alloy  30-50 35-55 40-70
Cr - Co AJ/oys 60-80 65-85 70-90
Duplex F51 60-80 65-85 70-90
Super duplex F55 30-50 40-60 50-70
HRSA hastelloy 30-50 40-60 50-70
HRSA incoinel 625 30-50 40-60 50-70
HRSA incoinel 718 30-50 40-60 50-70
HRSA nimonic 60-80 70-90 80-90
Titanium 60-80 70-90 80-90
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended