Alu Mac

133 Series

High Performance Corner Radius Endmil

Finish
Rough
 
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended

133 Series

StockOrder No.CodeOld Coded1h6d2h6d3l1l2l3CornerRelated Document
59100133.3.0300.0580.R0015.0080.0280.0130.00.S06E2V01.01133303015362.8058813R 0.15
59102133.3.0300.0580.K0000.0080.0280.0130.00.S06E2V01.01133303000362.8058813Ch 0.00
59104133.3.0400.0580.R0015.0130.0380.0154.00.S06E2V01.01133304015463.80581315.40R 0.15
59106133.3.0500.0580.R0015.0130.0480.0210.00.S06E2V01.01133305015564.80581321R 0.15
59108133.3.0500.0580.K0000.0130.0480.0210.00.S06E2V01.01133305000564.80581321Ch 0.00
*59110133.3.0600.0580.R0020.0130.0550.0210.00.S06E2V01.01133306002665.50581321R 0.20
*59112133.3.0600.0580.R0050.0130.0550.0210.00.S06E2V01.01133306005665.50581321R 0.50
*59114133.3.0800.0640.R0025.0210.0750.0280.00.S08E2V01.01133308025887.50642128R 0.25
59116133.3.0800.0640.R0050.0210.0750.0280.00.S08E2V01.01133308005887.50642128R 0.50
59118133.3.0800.0640.R0100.0210.0750.0280.00.S08E2V01.01133308010887.50642128R 1.00
*59120133.3.1000.0730.R0030.0220.0950.0320.00.S10E2V01.0113331000310109.50732232R 0.30
*59122133.3.1000.0730.R0050.0220.0950.0320.00.S10E2V01.0113331000510109.50732232R 0.50
59124133.3.1000.0730.R0100.0220.0950.0320.00.S10E2V01.0113331001010109.50732232R 1.00
*59126133.3.1200.0820.R0030.0260.1150.0400.00.S12E2V01.01133312003121211.50822640R 0.30
*59128133.3.1200.0820.R0050.0260.1150.0400.00.S12E2V01.01133312005121211.50822640R 0.50
59130133.3.1200.0820.R0100.0260.1150.0400.00.S12E2V01.01133312010121211.50822640R 1.00
*59132133.3.1600.0930.R0040.0360.1550.0530.00.S16E2V01.01133316004161615.50933653R 0.40
59134133.3.1600.0930.R0100.0360.1550.0530.00.S16E2V01.01133316010161615.50933653R 1.00
59136133.3.1600.0930.R0200.0360.1550.0530.00.S16E2V01.01133316020161615.50933653R 2.00
*59138133.3.2000.1050.R0050.0410.1950.0540.00.S20E2V01.01133320005202019.501054154R 0.50
59140133.3.2000.1050.R0200.0410.1950.0540.00.S20E2V01.01133320020202019.501054154R 2.00

Feed Per Tooth (mm/tooth)

Ø ap=1.50Ø ap=1Ø ae=0.30Ø ae=0.20Ø ae=0.10Ø
3 0,050 0,061 0,120 0,160 0,200
4 0,056 0,068 0,130 0,178 0,221
5 0,062 0,076 0,152 0,190 0,240
6 0,068 0,080 0,161 0,200 0,262
8 0,072 0,083 0,168 0,210 0,281
10 0,075 0,088 0,173 0,220 0,300
12 0,084 0,093 0,200 0,260 0,325
16 0,090 0,103 0,240 0,300 0,360
20 0,100 0,112 0,280 0,340 0,400

Cutting Parameters

Material Slotting ap=1xØ / ae=1xØ Vc (m/min)  Shoulder Milling ap=1xØ/ ae=0,5xØ Vc (m/min) 
Aluminium alloys <%6 Si 380-430 380-430
<%12 Si 330-380 330-380
>%12 Si 200-250 200-250
Coper alloys 140-180 140-180
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended