Alu Mac

123 Series

High Performance Aluminium Endmill

Finish
Rough
 
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended

123 Short Series

Stock Code d1h6 d2 d3 l1 l2 l3 r Ch z
123302058 2 6 1.9 58 5 12 0.04 3
123302558 2.5 6 2.4 58 8 16 0.05 3
* 123303058 3 6 2.8 58 8 13 0.2 3
* 123304058 4 6 3.8 58 13 15.4 0.2 3
* 123305058 5 6 4.8 58 15 21 0.2 3
* 123306058 6 6 5.7 58 17 26 0.2 3
* 123308064 8 8 7.7 64 22 30 0.2 3
* 123310073 10 10 9.7 73 25 35 0.2 3
* 123312082 12 12 11.7 82 28 40 0.2 3
123314082 14 14 13.7 82 28 40 0.2 3
* 123316093 16 16 15.7 93 37 53 0.2 3
* 123320105 20 20 19.7 105 38 54 0.2 3

123 Long Series

Stock Code d1h6 d2h6 d3 l1 l2 l3 R Ch Z
* 123306108 6 6 5.8 108 15 45 0.2 3
* 123308108 8 8 7.8 108 18 62 0.2 3
* 123310108 10 10 9.8 108 20 62 0.2 3
* 123312125 12 12 11.8 125 25 80 0.2 3
123312150 12 12 11.8 150 32 105 0.2 3
123316110 16 16 15.7 110 50 60 0.2 3
* 123316160 16 16 15.8 160 30 110 0.2 3
123320200 20 20 19.8 200 30 115 0.2 3

Feed Per Tooth (mm/tooth)

Ø ap=1.50Ø ap=1Ø ae=0.30Ø ae=0.20Ø ae=0.10Ø
3 0.05 0.061 0.12 0.16 0.2
4 0.056 0.068 0.13 0.178 0.221
5 0.062 0.076 0.152 0.19 0.24
6 0.068 0.08 0.161 0.2 0.262
8 0.072 0.083 0.168 0.21 0.281
10 0.075 0.088 0.173 0.22 0.3
12 0.084 0.093 0.2 0.26 0.325
16 0.09 0.103 0.24 0.3 0.36
20 0.1 0.112 0.28 0.34 0.4

Cutting Parameters

Material Slotting ap=1.5-1.0Ø Vc (m/min)  Shoulder Milling ap=1.5Ø / ae=0.3 - 0.2 - 0.1Ø Vc (m/min) 
Aluminium alloys 250-300 350-400
Coper alloys 200-250 300-350
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended