Ultra Bite

114 Short Series Endmill

Ultra-Bite Series
Ultra-Bite Series
Corner Radius Endmil

Finish
Rough
 
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended

114 Ultra-Bite Short Series

STOCK CODE d1h9 l2 l3 d3 l1 d2h6 R Z
* 114402005 2 2 12 1.9 58 6 0.5 4
* 114403005 3 3 16 2.8 58 6 0.5 4
* 114404005 4 4 20 3.8 58 6 0.5 4
* 114404010 4 4 20 3.8 58 6 1 4
114405005 5 5 18 4.8 58 6 0.5 4
114405010 5 5 18 4.8 58 6 1 4
114405015 5 5 18 4.8 58 6 1.5 4
* 114406005 6 6 23 5.8 58 6 0.5 4
* 114406010 6 6 23 5.8 58 6 1 4
* 114406015 6 6 23 5.8 58 6 1.5 4
* 114408005 8 8 25 7.7 64 8 0.5 4
* 114408010 8 8 25 7.7 64 8 1 4
* 114408015 8 8 25 7.7 64 8 1.5 4
* 114410005 10 10 32 9.7 73 10 0.5 4
* 114410010 10 10 32 9.7 73 10 1 4
114410015 10 10 32 9.7 73 10 1.5 4
* 114412005 12 12 36 11.7 82 12 0.5 4
* 114412010 12 12 36 11.7 82 12 1 4
* 114412015 12 12 36 11.7 82 12 1.5 4
114412020 12 12 36 11.7 82 12 2 4
114416010 16 16 43 15.5 93 16 1 4
114416015 16 16 43 15.5 93 16 1.5 4
114416020 16 16 43 15.5 93 16 2 4
114416030 16 16 43 15.5 93 16 3 4

114 Ultra-Bite Long Series

STOCK CODE d1h9 l2 l3 d3 l1 d2h6 R Z
114U404005 4 10 20 3.8 74 6 0.5 4
114U406005 6 16 22 5.8 74 6 0.5 4
114U406010 6 16 22 5.8 74 6 1 4
114U408005 8 16 24 7.7 74 8 0.5 4
114U408010 8 16 24 7.7 74 8 1 4
114U408015 8 16 24 7.7 74 8 1.5 4
114U410010 10 18 32 9.7 100 10 1 4
114U410015 10 18 32 9.7 100 10 1.5 4
114U410020 10 18 32 9.7 100 10 2 4
114U412010 12 20 36 11.7 100 12 1 4
114U412015 12 20 36 11.7 100 12 1.5 4
114U412020 12 20 36 11.7 100 12 2 4

Feed Per Tooth (mm/tooth)

Ø ae=0.25Ø ae=0.20Ø ae=0.15Ø ae=0.10Ø ae=0.15Ø ae=0.10Ø
4 0.031 0.034 0.037 0.04 0.044 0.047
6 0.031 0.034 0.037 0.041 0.045 0.049
8 0.038 0.042 0.047 0.053 0.058 0.066
10 0.049 0.052 0.056 0.061 0.066 0.071
12 0.052 0.056 0.062 0.068 0.074 0.079
16 0.063 0.068 0.076 0.082 0.089 0.097

Cutting Parameters

Material Shoulder Milling Finish Milling
ap=0.10Ø / ae=0.25 - 0.10Ø ap=0.10Ø / ae=0.10Ø
Vc (m/min)  Vc (m/min) 
Cold work tool steel 110-150 150-180
Hot work tool steel 100-140 140-170
Gray cast 70-100 100-130
Alloyed cast 70-100 100-130
Precision cast 65-90 90-120
≤ 54 HRC 65-90 90-120
>54 HRC 60-80 80-110
Steel
Stainless Steel
Hardened Steel ≤ 54 HRc
Hardened Steel > 54 HRc
Cast
Graphite
Non Ferrous Material
HRSA
Titanium
  • Recommended
  • Acceptable
  • Not Recommended