Ultra Bite

110 Series Endmill

Ultra-Bite Series

Ultra-Bite Series

Fnishing Endmill

Finish

Rough

	Steel
	Stainless Steel
	Hardened Steel ≤ 54 HRc
	Hardened Steel > 54 HRc
	Cast
	Graphite
	Non Ferrous Material
	HRSA
	Titanium

Recommended
Acceptable
Not Recommended

110 Short Ultra-Bite Series

Stock	Code	d1h9	d2h6	l1	l2	Ch	Z
*	110606058	6	6	58	15	0.1	6
*	110608064	8	8	64	19	0.1	6
*	110610073	10	10	73	22	0.1	6
*	110612082	12	12	82	26	0.1	6
*	110614082	14	14	82	31	0.15	6
*	110616093	16	16	93	32	0.15	6
	110818093	18	18	93	32	0.15	8
	110820105	20	20	105	38	0.15	8

110 Long Ultra-Bite Series

Stock	Code	d1h9	d2h6	l1	l2	Ch	Z
*	110606080	6	6	80	30	0.1	6
*	110608090	8	8	90	40	0.1	6
*	110610100	10	10	100	45	0.1	6
*	110612110	12	12	110	55	0.1	6
*	110614110	14	14	110	60	0.15	6
*	110616125	16	16	125	70	0.15	6
	110818140	18	18	140	70	0.15	8
	110820150	20	20	150	75	0.15	8

Feed Per Tooth (mm/tooth)

Ø	ae=0.25Ø	ae=0.20Ø	ae=0.10Ø
6	0.028	0.03	0.024
8	0.046	0.051	0.045
10	0.054	0.059	0.051
12	0.06	0.066	0.057
14	0.064	0.074	0.063
16	0.073	0.079	0.069
18	0.078	0.086	0.074
20	0.085	0.092	0.08

Cutting Parameters

Material	Slotting	Shoulder Milling

	ap=2.0Ø / ae=0.25Ø	ap=2.0Ø / ae=0.20- 0.10Ø
	Vc (m/min)	Vc (m/min)
Unalloyed steel	100-140	140-170
Steel	80-110	110-140
Tempered steel	80-100	105-130
Cold work tool steel	60-80	80-105
Hot work tool steel	60-80	80-105
AISI 304 - 416 - 420	40-60	55-80
AISI 316 - 440	40-60	55-80
17-4 PH 15-5 PH	40-60	55-80
Cobalt-Chrome alloys	40-60	55-80
Duplex F51	40-60	55-80
Super duplex F55	40-60	55-80
Gray cast	80-110	110-140
Alloyed cast	80-100	105-130
Precision cast	80-100	105-130
Titanium	190-230	230-260
Titanium alloys	140-180	180-220
>54 HRC	30-50	50-70

	Steel
	Stainless Steel
	Hardened Steel ≤ 54 HRc
	Hardened Steel > 54 HRc
	Cast
	Graphite
	Non Ferrous Material
	HRSA
	Titanium

Recommended
Acceptable
Not Recommended